Cummins ISX Cylinder Head Problems: What Actually Fails and Why
Most Cummins ISX cylinder head problems come down to three things: injector sleeve seal leaks that mix fuel and coolant, head gasket fretting against the head's combustion face, and cracks at the injector bores. Cummins covers the sleeve leak in two bulletins, TSB170004 for dual cam and TSB170002 for single cam, and on single cam engines a leaking sleeve alone is not a reason to replace the head.
Which ISX head do you have: dual cam or single cam?
Answer this first. The bulletins, the fixes and the replacement heads all split along this line, and the two heads do not interchange. Get it wrong and you buy the wrong head.
Dual overhead cam. The ISX entered production in 1998 as a dual overhead cam engine, with one camshaft driving the injectors and the other running the valve train, and it stayed that way until 2010 (Engine Builder). Cummins groups these as the DOHC ISX: the CM570, CM870 and CM871 (Cummins).
Single overhead cam. Cummins calls the later engines the SOHC ISX, covering all ISX, QSX and X15 CM2250 and CM2350 configurations. One camshaft rides in the head.
If you're not sure, pull the valve cover and count camshafts, or call us at (713) 675-2435 with the engine serial number and we'll match the head. For single cam engines we carry the new loaded ISX15 / X15 SOHC cylinder head, 4374091. For dual cam engines there is a new ISX dual cam cylinder head for the CM570, CM870 and CM871. Loaded means the valves, springs, seals and guides are already installed, ready to bolt on.
What are the most common Cummins ISX cylinder head problems?
Three head problems are worth sorting out before you order parts. Two of them look the same from the driver's seat, so each starts with a different check.
| Problem | Engines | What you see | Check first | Usual fix |
|---|---|---|---|---|
| Injector sleeve (cup) seal leak | Dual cam CM570, CM870, CM871 (TSB170004); single cam ISX15 and X15 (TSB170002) | Fuel in coolant, coolant in fuel, fault code 418, pressurized cooling system | Rule out fuel heaters and other sources per the bulletin troubleshooting, then pressurize the cooling system (Procedure 002-014) | Single cam: retaining ring 4312298 in all six sleeves. Dual cam out of warranty: optional blue O-ring 5440257 on all injectors |
| Head gasket fretting | ISX15 per Cummins TSB200018; other ISX engines, check QuickServe | Repeat gasket failures; wear scarring on the head's combustion face | Combustion face at every cylinder; liner protrusion and counterbore condition against the service manual | Correct whatever is out of spec, then a new gasket set and head bolt kit |
| Crack at the injector bore | Any ISX; no Cummins bulletin we can cite | Coolant crossover or loss that continues after sleeve causes are ruled out | Coolant passage leak test with the head off (Procedure 002-004, from TSB170004) | Bench decision against OEM limits; replace if it can't be restored |
The order matters. A sleeve leak and a cracked injector bore both put coolant where it doesn't belong, but on a single cam engine one is fixed with six retaining rings and the other means a head on the bench. Prove which one you have before you buy a head.
One caution for dual cam owners: owners of CM870 and CM871 engines, many of them in motorhomes, report broken valves in the #6 cylinder. We have not found a Cummins bulletin on it, so treat it as unconfirmed. If a valve drops on any ISX, inspect the piston, liner and turbo before you price a head-only job.
Why is there coolant in the fuel or fuel in the coolant on an ISX?
The usual suspect is a leaking injector sleeve seal, but Cummins makes you prove it. Both sleeve bulletins give the same root cause: "Shrinkage of injector sleeve seal material can create a leak path between cylinder head cooling jacket and injector bore." The injector sits in a sleeve with the coolant jacket around it, so once that seal shrinks, fuel and coolant cross over. The listed symptoms are:
- Fuel in the coolant
- Coolant in the fuel
- Fault code 418, the water-in-fuel indicator
- A pressurized cooling system
TSB170004 calls seal shrinkage "only one possible cause." Work it in this order:
- Follow the published troubleshooting and rule out other sources of contamination, such as fuel heaters, before you look at the sleeves.
- With the head on the engine, verify the leak by pressurizing the cooling system per Service Manual Procedure 002-014, Section 2.
- If the head is already off, leak test the coolant passage per Procedure 002-004, Section 2.
- Inspect the fuel tank and filters for contamination, as the 2019 release of TSB170004 directs.
Don't skip step 4. Contaminated fuel left in the tank goes straight back through the repaired engine, and fuel contamination is one of the conditions that voids TTM's warranty on a replacement head. On EGR engines with coolant loss but no fuel crossover, check the EGR cooler before you blame the head.
Dual cam ISX: Cummins TSB170004
TSB170004 covers the ISX CM570, CM870, CM871 and CM871 E, plus the QSX CM570. The tell is progressive damage on the lowest injector O-ring, the green one, part number 3347937. The fix changed between releases:
- 2017 release: replace green O-ring 3347937 with blue O-ring 5440257 on all injectors.
- 2019 release: the same parts, now labeled an "Optional Repair," with a leak check required after the injectors go back in.
- Heads under Cummins warranty: the 2019 release says a head with base, extended or parts warranty coverage that has leaking injector sleeves "must" be replaced. The optional repair is not for components in warranty.
Work from the 2019 release. If the crossover comes back after the O-ring repair has been done once, Cummins says the head would need to be replaced.
Single cam ISX15 and X15: Cummins TSB170002
The 2017 release of TSB170002 lists the ISX15 CM2250, ISX15 CM2250 SN and X15 CM2350 X114B. The May 7, 2019 re-release lists the ISX15 CM2250, CM2250 SN and CM2350 X101, and the list runs on past what we could read. Check the latest revision in QuickServe against your engine serial number. The instructions are blunt:
- "Cylinder head assemblies are not to be replaced if injector sleeve is found leaking."
- Install retaining ring 4312298 in all six injector sleeves, using service tool 5394735, per Procedure 002-014, Section 2.
- Cummins says the repair should only be done once.
- If a sleeve leaks again with a ring installed, Procedure 002-014 directs further investigation of the head, and Cummins says the head should be replaced when leaking cups are found with rings already present.
That's the decision line. No ring yet: ring all six and keep the head. Ring installed and still leaking: plan on a head. If you're replacing a single cam head anyway, ask us whether the sleeves in the new head already carry the retaining ring, so you know whether 4312298 belongs on your parts list. While the injectors are out, inspect the ISX15 / X15 injector fuel supply connectors, 2894829 and replace any that are damaged.
Why does my ISX keep blowing head gaskets?
A gasket that keeps failing is telling you something about what it's clamped between, so look at the head face, the liners and the block before you blame the gasket. Cummins bulletin TSB200018, dated January 23, 2020, is listed against the ISX15 for "verification and resolution of fretting of the head gasket combustion seal against the cylinder head combustion face," which leaves wear scarring on the face (summary in an index of NHTSA-filed Cummins bulletins). We have not read the full text, so pull the current bulletin for your serial number from QuickServe or a Cummins dealer before you plan the repair around it.
A scarred head face won't seal a new gasket any better than it sealed the old one. Before a new gasket or head goes on:
- Inspect the old head's combustion face for fretting scars at every cylinder, not just the one that failed.
- Measure liner protrusion and check counterbore condition against the Cummins service manual specs for your engine serial number. We don't print those numbers; get them from QuickServe.
- Correct anything that's out of spec before the new gasket goes on. The gasket only seals as well as the surfaces it's clamped between.
- Judge the head face against the OEM limits. A face outside those limits means a replacement head.
- Clean and dry every bolt hole and use a new head bolt kit. Torque values, angle and tightening sequence come from the Cummins service manual for your engine.
Single cam engines take the ISX15 head gasket set, 4376104 and the ISX15 / X15 head bolt kit, 3678506 / 3678804. Dual cam engines use the ISX dual cam upper gasket set, 4352145. Our head bolt kit is listed for the ISX15 and X15, so confirm dual cam bolt fitment with us before you order.
Why do ISX heads crack at the injector bores?
There's no single published cause we can point you to. We found no Cummins bulletin we can cite that pins combustion-face cracks on one root cause, so be wary of any one-line explanation. What Cummins does give you is the test: with the head off, leak test the coolant passage per Procedure 002-004, Section 2, as TSB170004 directs for the dual cam engines. On a single cam engine, use the matching coolant passage test in the service manual for your serial number.
The practical problem is that a crack at the injector bore and a leaking sleeve seal produce the same symptoms. That's why the sleeve bulletins come first. If the one-time sleeve repair has been done and the crossover returns, or the coolant passage test fails with the head on the bench, you're looking at the casting.
Find the cause before the replacement goes on. The conditions that void TTM's warranty are the same ones to rule out on the old engine: overheating, inadequate cooling, low coolant or oil, over-fueling and fuel contamination. Check the water pump, radiator, thermostat and fan, and look at the fuel system and any tuning history. Some mechanics report repeat cracking after EGR deletes and timing-changing tunes; that is field opinion, not an OEM finding, but over-fueling damage is excluded from coverage either way. If the cooling system is suspect, we carry a new ISX water pump, 3684449; confirm fitment with your serial number.
Repair or replace: how do you decide?
Keep the head when the bulletin fix applies and hasn't been used yet. Replace it when the bulletin fix has already failed, when Cummins requires replacement, or when the casting fails a leak test and can't be brought back to OEM limits. In order:
| Situation | Call |
|---|---|
| Single cam, leaking sleeve, no retaining rings yet | Install ring 4312298 in all six sleeves per TSB170002; keep the head |
| Single cam, leaking again with rings installed | Replace the head, per Procedure 002-014 and Cummins guidance |
| Dual cam, crossover, head under Cummins warranty | The 2019 TSB170004 says the head must be replaced; go through a Cummins dealer |
| Dual cam, crossover, out of warranty, first occurrence | Rule out fuel heaters, verify the leak, then the optional blue O-ring 5440257 repair and leak check |
| Dual cam, crossover returns after the O-ring repair | Replace the head |
| Head off, coolant passage leak test fails | Machine shop judges it against OEM limits; replace if it can't be restored |
| Fretting on the head face, repeat gasket failures | Correct liner protrusion and counterbore condition to spec first, then judge the head face against OEM limits |
| Dropped valve, any cylinder | Inspect piston, liner and turbo before pricing a head-only job |
Count the downtime, not just the part. You pay for teardown, inspection and freight whether the head gets repaired or replaced, and if the bench finds more than you expected, you're buying a head anyway with the truck down the whole time. Head removal and installation labor varies with the chassis and the shop, so get your shop's quote first. TTM's warranty does not cover labor.
What should you check before ordering a new ISX head?
- Engine serial number and CM designation. Confirms dual cam or single cam, the right head and which bulletin revision applies.
- Retaining rings. On a single cam head, ask whether the sleeves already carry the TSB170002 ring before you order 4312298.
- A new head bolt kit. We recommend new bolts on every head job. Confirm reuse rules, torque, angle and sequence in the Cummins service manual.
- The right gasket set for a dual cam or single cam engine.
- Liner protrusion and counterbores, measured to the service manual spec.
- A clean fuel system if coolant got into the fuel: tank and filters inspected.
- The cooling system, since overheating, low coolant and inadequate cooling void TTM's warranty.
- Overhead adjustment. Set it at install to the values and procedure in the service manual for your engine serial number. After that, Cummins puts the first overhead adjustment at 500,000 miles on the ISX and X15 (Transport Topics), and its maintenance guides list 500,000 miles, 10,000 hours or 60 months for X15 EPA 2017 (Cummins) and EPA 2024 engines (Cummins).
What does TTM's warranty cover on an ISX head?
New cylinder heads from TTM carry a 12-month warranty against defects in material and workmanship unless the product page says otherwise, and there is no core charge on new heads. Coverage on engine components by type:
- New: 12 months, unless otherwise written
- Remanufactured or long block: 12 months
- Reconditioned: 3 months
- Good used, tested and inspected: 30 days
The warranty does not cover labor, diagnostics, removal and installation, towing, freight, downtime, lost revenue, rental equipment or driver costs. Damage from improper installation, inadequate cooling, fuel contamination, over-fueling, overheating, low oil or coolant, skipped break-in or non-OEM fluids voids coverage, which is one more reason to fix whatever killed the old head before the new one goes on. If you find a problem, notify us within 72 hours and don't tear down the engine until TTM authorizes it in writing. Full terms are on the TTM warranty and returns page.
Frequently asked questions
How do I know if my ISX cylinder head is cracked?
You prove it by testing, not by symptoms. A leaking injector sleeve seal causes the same fuel and coolant crossover, so rule that out first with Cummins TSB170004 for dual cam engines or TSB170002 for single cam engines. In the truck, pressurize the cooling system per Service Manual Procedure 002-014. With the head off, leak test the coolant passage (Procedure 002-004, cited in TSB170004). If that test fails, or the crossover returns after the one-time sleeve repair, suspect the casting.
What is fault code 418 on a Cummins ISX?
Fault code 418 is the water-in-fuel indicator. Cummins lists it as one of four symptoms of injector sleeve seal leakage in TSB170004 and TSB170002, alongside fuel in the coolant, coolant in the fuel and a pressurized cooling system. Check the fuel filter for coolant before you assume it's water from the tank, and rule out other sources such as fuel heaters before you blame the head.
Will a single cam ISX15 head fit a dual cam ISX?
No. The dual cam ISX (CM570, CM870, CM871) carries two camshafts in the head, one for the injectors and one for the valve train. The CM2250 and CM2350 single cam engines carry one. The heads are different designs and do not interchange. Count camshafts under the valve cover, or give us the engine serial number at (713) 675-2435 before you order.
Does a leaking injector sleeve mean I need a new ISX head?
Not the first time on a single cam engine. Cummins TSB170002 says heads are not to be replaced for a leaking sleeve; install retaining ring 4312298 in all six sleeves, once. If cups leak again with rings installed, Cummins says replace the head. On dual cam engines, the 2019 TSB170004 requires a new head if it is under Cummins warranty. Out of warranty, the blue O-ring repair is optional, and a repeat leak means a new head.
Can a cracked ISX head be repaired instead of replaced?
Sometimes, but it's a bench decision, not a phone diagnosis. A coolant passage leak test on the removed head (Procedure 002-004) and a close inspection show where the crack runs and how far. Repair only makes sense if the head can be returned to the OEM limits in the service manual. Weigh the machine shop quote, freight and downtime against a new loaded head, and find what cracked it before either goes back on.
Do I have to replace the head bolts on an ISX?
We recommend a new head bolt kit on every ISX head job, because it takes one variable out of a repair that is expensive to do twice. Confirm bolt reuse rules, torque values, angle and tightening sequence in the Cummins service manual for your engine serial number, and clean and dry every bolt hole first. Our kit, 3678506 / 3678804, is listed for the ISX15 and X15; confirm dual cam fitment with us.
How often should the overhead be adjusted on an ISX or X15?
Cummins puts the first overhead adjustment at 500,000 miles on the ISX and X15, according to Transport Topics. Cummins' maintenance guides for X15 EPA 2017 and EPA 2024 engines list the overhead adjustment at 500,000 miles, 10,000 hours or 60 months. After a head replacement, set the overhead at installation to the values and procedure in the Cummins service manual for your engine serial number.
Is a new ISX head better than a remanufactured one?
Both can be the right buy. A new head has no service history, and a remanufactured head that has been properly tested is a legitimate option too. At TTM, new and remanufactured engine components both carry 12 months, reconditioned parts 3 months and good used tested parts 30 days. Whichever you buy, fix what killed the old head first, or the replacement fails the same way.
Sources
- Cummins TSB170004: Injector Sleeve Seal Leakage, Optional Repair, 2019 release (NHTSA)
- Cummins TSB170004, 2017 release (NHTSA)
- Cummins TSB170002: Injector Sleeve Seal Leakage, single cam, 2019 re-release (NHTSA)
- Cummins TSB170002, 2017 release (NHTSA)
- Cummins: ISX injector sleeve leakage, DOHC and SOHC engines
- Engine Builder: Generating Strength, the Cummins ISX Engine
- Cummins X15 EPA 2017 maintenance quick reference, asset 0032808
- Cummins X15 EPA 2024 maintenance quick reference, asset 0077777
- Transport Topics: More Frequent Overhead Maintenance Worth the Trouble
- Index of NHTSA-filed Cummins ISX15 service bulletins